Fairing and Gas Tank Heatshield Mat

Motorcycle gas tank heat shield

More Views

1100°F

593°C

CONTINUOUS

2000°F

1093°C

Intermittent

FEATURES:

  • Lowers fuel temperature by as much as 10°F

  • Keeps fuel’s chemical balance in tact

  • Also great for air boxes and under seats

  • Adhesive backing sticks to almost any clean surface-not recommended for rough/unfinished fiberglass

  • Bulk rolls and custom widths available, minimums apply

  • Made in the USA

Part No Description
721006 0.032 thk x 18 in x 18 in
721010 0.032 thk x 12 in x 24 in, tank heat shield
721011 0.032 thk x 24 in x 24 in fairing heat shield
721013 0.032 thk x 24 in x 48 in

Moto Heatshield Mat is a heat shield for the bottom of your fuel tank, air box, fairings, bags, and seat bottom. It offers fuel tank protection and prevents your fuel from boiling, stops pre-ignition, prevents critical components of your fuel from evaporating. This can prevent vapor lock and helps to keep your bike performance as crisp as it was when you started the race. You can also use this as a heat shield on your air box, to lower air intake temperatures by shielding radiant heat from your exhaust and shock. This will further improve the efficiency of your motor and create more horsepower as well as provide fairing protection. Moto Heatshield Mat can also be used as a fairing heat shield, helping to prevent them from melting and ruining paint. It can also be used as a heat shield for the bottom of your seat or on the bags on your custom cruiser. Face the aluminized side toward the source of radiant heat (we recommend a minimum 1” of airspace) to shield heat away. This product withstands 1100-degrees of radiant heat and up to 450-degrees Fahrenheit of direct heat. It cuts easily with a pair of scissors, and the high temperature peel and stick adhesive will stick to any clean surface.

To add increased life and protection, line the outside edge of our Moto Heatshield Mat with our Moto Shield Tape. This will protect it when using a high power washer and help prevent water damage to mat.

Download HP Heatshield Mat Instruction Sheet




HP Heatshield Mat Installation tips:

  • Be sure to use a 1" air-gap between HP Heatshield Mat and heat source for best results
  • HP Heatshield Mat is intended to be applied on the cold side of panel or component, i.e. it is not intended to direct contact with heat source

Required tools:

  • Heavy duty scissors or utility knife 
  • Carburetor cleaner or other degreaser
  • Pre-paint cleaner or other non residue cleaner
  • 3M Super Trim adhesive or other spray adhesive (Part #720305 & 720505 only)
  • Poster board, heavy paper - optional

PRO TIP - Use poster board or butcher paper to make a template. For surfaces with severe bends, it may be necessary to cut relief lines or wedges to get product to conform. Transfer template to HP Heatshield Mat and cut.

  1. Panel or component surface temperature should be at least 65°F, sticking onto anything colder may not allow adhesive to set up properly.
  2. Degrease and clean surface of any residual chemicals, using carburetor spray or other cleaner/degreaser.
  3. We strongly recommend rubbing the surface with a pre-paint cleaner or isopropyl alcohol (or other non-residue cleaner) after cleaning and degreasing. For part # 720305 & 720505, without adhesive, skip to Step 7
  4. Carefully peel the adhesive backing off theHP Heatshield Mat. Start peeling from one corner.
  5. Lay the HP Heatshield Mat, start on one edge of panel or component and work out slowly to ensure no “bubbles” occur. Air bubbles will cause the material to not stick and fall off.
  6. Press the HP Heatshield Mat firmly onto the panel/component, hold while pressing down for 2 minutes. Skip to Step 9
  7. Non adhesive product only - Use 3M Super Trim or Super 77 Adhesive. After HP Heatshield Mat has been cut, spray back of cloth and panel or component you are applying HP Heatshield Mat to.
  8. Allow adhesive to get tacky and apply cloth, start on one edge of panel or component and work out slowly to ensure no “bubbles” occur. Air bubbles will cause the material to not stick and fall off. Press firmly for 2 minutes.
  9. Optional - If using edge tape like Cool Foil Tape, clean the edge of HP Heatshield Mat with the pre-paint cleaner or isopropyl alcohol.
  10. Optional - Pre-fit and trim tape to fit the HP Heatshield Mat.
  11. Optional - It is important to do one edge/seam at a time with the edge tape.
  12. Optional - Peel adhesive backing off tape, press and firmly hold in place for 2 minutes.

More information coming soon!

More information coming soon!

Use Moto Heatshield Mat on:

  • Fairings
  • UTV firewall
  • Gas tanks
  • heatshieldproducts (844) 723-2665