Inferno Wrap - Exhaust Pipe Wrap for your Turbo Bike, Snowmobile, or UTV

Racing Exhaust Pipe Wrap

More Views








  • Reduces radiant heat from pipe up to 50%

  • Increases horsepower

  • All rolls 1/16” thick

  • May require re-jetting of carburetors

  • Made in the USA

Part No Description
325001 1 in x 25 ft Roll
325002 1 in x 50 ft Roll
325025 2 in x 25 ft Roll
325050 2 in x 50 ft Roll

Exhaust pipe wrap will sustain the extreme temperatures that your glowing pipes from your racing snowmobile, motorcycle, cart, or other extreme riding applications require!

Tired of your alleged 2000°F exhaust thermal wrap becoming brittle and falling apart? Then this header pipe wrap is for you! Unlike other forms of heat wrap for exhaust pipes, the Inferno Header Wrap is manufactured from texturized amorphous silica filament yarn; this makes this exhaust pipe wrap strong and flexible while operating at its designed service temp of 2000-degrees Fahrenheit continuous and 3000-degrees Fahrenheit intermittent. There is not a header or exhaust insulating wrap on the market that will take higher temperatures and last longer. Inferno header wrap maintains hotter exhaust gases, decreases the density, and that allows the exhaust gas to exit the system faster! Increased exhaust scavenging is produced: that equals more horsepower. Inferno Heat Wrap for exhaust pipes also reduces radiant heat from exhaust pipes by as much as 50 percent. Finally you can wrap that turbo snowmobile or turbo super bike and be worry free.

If you don’t like the color simply spray the Inferno Header Pipe wrap with some quality exhaust paint. You don’t need expensive silicone sealer spray, just walk into an auto parts store and buy an off the shelf exhaust paint in the color of your choice.

This exhaust pipe wrap can be fastened with Thermal-Tie, HP tie Wire, or hose clamps.

How much Inferno Exhaust Pipe Wrap do you need? Click here for our exhaust wrap calculator

Download Exhaust Wrap Instruction Sheet

MSDS | Specification Sheet | Brochure | Brochure (printer friendly)

Insulation type: Insulator, retains heat in

Material: Silica

Header and Exhaust Wrap Calculator


This calculator is a tool to estimate how much exhaust header wrap you will need for your headers, downpipe, or exhaust system. Calculations are a guide only! Actual usage will vary depending upon installation. Tighter installation of exhaust wrap on the pipe results in smaller header wrap needed.


All fractions should be in decimal form:
  • 1/8 should be 0.125
  • ¼ should be 0.250
  • ½ should be 0.500
  • ¾ should be 0.750
  • 7/8 should be 0.875


  • ¾"- 2" pipe OD use 1" wide wrap
  • 1¾"- 4" pipe OD use 2" wide wrap
  • 3"- 4" pipe OD use 2" or 3" wide wrap
  • 4"- 5" pipe OD use 2", 3" or 4" wide wrap
  • 5"+ pipe OD use 3", 4" or 6" wide wrap


¼" Overlap is recommended for automotive applications, a 50% overlap is recommended for all motorcycle, UTV, kart, marine, heavy duty and industrial applications.


  * Pipe diameter in inches
  * Pipe length in feet
  Number of bends less than 45°
  Number of bends greater than 45°
  * Required field  


  Feet of 1" exhaust wrap needed:
  25' rolls   50' rolls   100' rolls    
  Feet of 2" exhaust wrap needed:
  15' rolls   25' rolls   50' rolls   100' rolls
  Feet of 3" exhaust wrap needed:
  100' rolls            
  Feet of 4" exhaust wrap needed:
  100' rolls            
  Feet of 6" exhaust wrap needed:
  100' rolls            

heatshieldproducts (844) 723-2665