Heat Shield Sleeve with Velcro

Thermaflect Sleeve-Velcro

More Views

1100°F

593°C

CONTINUOUS

2000°F

1093°C

Intermittent

FEATURES:

  • Capable of reflecting up to 90% of radiant heat

  • Helps to prevent vapor lock, lower air intake temperatures, protects wires from melting

  • Also available in a sewn seam

  • Made in the USA

Part No Description
274012 1/2 id x 3 ft Velcro seam
274013 1/2 id x 10 ft Velcro seam
274034 3/4 id x 3 ft Velcro seam
274035 3/4 id x 10 ft Velcro seam
274100 1-in id x 3 ft Velcro seam
274101 1-in id x 10 ft Velcro seam
274112 1-1/2 id x 3 ft Velcro seam
274113 1-1/2 id x 10 ft Velcro seam
274114 1-1/4 id x 3 ft Velcro seam
274115 1-1/4 id x 10 ft Velcro seam
274134 1-3/4 id x 3 ft Velcro seam
274135 1-3/4 id x 10 ft Velcro seam
274200 2-in id x 3 ft Velcro seam
274201 2-in id x 10 ft Velcro seam
274212 2-1/2 id x 3 ft Velcro seam
274213 2-1/2 id x 10 ft Velcro seam
274214 2-1/4 id x 3 ft Velcro seam
274215 2-1/4 id x 10 ft Velcro seam
274234 2-3/4 id x 3 ft Velcro seam
274235 2-3/4 id x 10 ft Velcro seam
274300 3-in id x 3 ft Velcro seam
274301 3-in id x 10 ft Velcro seam
274304 3-1/2 id x 3 ft Velcro seam
274305 3-1/2 id x 10 ft Velcro seam
274308 4-in id x 3 ft Velcro seam
274309 4-in id x 10 ft Velcro seam
274310 4-1/2 id x 3 ft Velcro seam
274311 4-1/2 id x 10 ft Velcro seam
274312 5-in id x 3 ft Velcro seam
274313 5-in id x 10 ft Velcro seam
274314 5-1/4 id x 3 ft Velcro seam
274315 5-1/4 id x 10 ft Velcro seam

Shield your wiring, lines, and cables safe from heat, without disassembling them. Thermaflect Sleeve acts as a thermal barrier capable of reflecting up to 90% of radiant heat away (requires minimum of 1" of airspace and good aiflow). It is excellent to use as a fuel line heat sleeve, on wiring looms, air intake, intercooler pipes, and air conditioner hoses. By keeping fuel and air intake temperatures cool it helps to prevent vapor lock, improves performance, improves mileage and also reduces fuel evaporation and vapor lock. Weight there is more; a 3' length our Thermaflect Sleeve weighs less than 6" of the silicone covered stuff of the same diameter. Though it weighs much less, it offers superior radiant heat protection. Thermaflect Sleeve withstands 1100-degrees Fahrenheit of continuous radiant heat and 500-degrees Fahrenheit direct heat. Also available in sewn seam.



 

  • Face velcro seam in opposite direction of heat source
  • Be sure ends of sleeve are sealed or secured to component you are trying to protect. You can seal the ends using our Thermaflect Tape, Cool Foil Tape, Thermal-Tie, shrink tube, or any mechanical fastener. Securing the ends will ensure no hot air sneaks in behind the sleeve, thus allowing it to work more efficiently.
  • It also functions better if the heat shield sleeve is tight on the component

MSDS | Specification Sheet | Brochure


Insulation type: Thermal Barrier, designed to shield radiant heat

Base material: Fiberglass

Color: Silver/Chrome


AN SLEEVING CALCULATOR

Disclaimer:

The following conversion is a guide for AN hoses only. The conversion reflects the most common conversions for AN hose sizes, however there may be some variances with different manufacturer's. Always double check by measuring the OD of your hose. Always verify the OD of your hose, you may use a caliper or sliding an open end wrench over the hose. If you are still unsure verify with the manufacturer of the hose as to their specific OD. By using this calculator you acknowledge this is a guide only and it is ultimately your responsibility to verify the correct OD of your AN line.

ENTER AN HOSE SIZE WITHOUT DASH:

:

RESULTS:

 

:

:

:

More information coming soon!

More information coming soon!

heatshieldproducts (844) 723-2665