HD Fire Shield Sleeve

HD Fire Shield Sleeve

More Views

500°F

260°C

CONTINUOUS

900°F

482°C

Intermittent

FEATURES:

  • Continuous operating temperature of 500°F, 900°F intermittent

  • Silicone layer can be cleaned and protects against abrasion

  • Larger diameters also available up to 4" ID

  • Reduces and dissipates heat

  • Always wear safety glasses, dust mask, gloves and long sleeves are recommended when handling this product.

  • Made in the USA

Part No Description
210011 3/8-id x 10 ft Red
210013 1/2-id x 10 ft Red
210015 3/4-id x 10 ft Red
210017 1in id x 10 ft Red
210019 1-1/4 id x 10 ft Red
210021 1-1/2 id x 10 ft Red
210041 3/8-id x 10 ft Black
210043 1/2-id x 10 ft Black
210045 3/4-id x 10 ft Black
210047 1in id x 10 ft Black
210049 1-1/4 id x 10 ft Black
210051 1-1/2 id x 10 ft Black
210110 3/8 id x 100 ft Red
210112 1/2 id x 100 ft Red
210114 3/4 id x 50 ft Red
210116 1 id x 50 ft Red
210118 1-1/4 id x 50 ft Red
210120 1-1/2id x 50 ft Red
210140 3/8 id x 100 ft Black
210142 1/2 id x 100 ft Black
210144 3/4 id x 50 ft Black
210146 1 id x 50 ft Black
210148 1-1/4 id x 50 ft Black
210150 1-1/2id x 50 ft Black

Fire Heat Shield Sleeve provides thermal and physical protection with its rugged silicone covering. Starting with braided fiberglass yarns in a flexible substrate; it is then coated with a high grade silicone rubber. This rugged silicone coating makes the Fire Shield Sleeve resistant to most chemicals including hydraulic fluids, oils, and fuels. The coating on this HD sleeve also makes it resistant to abrasion and fraying. You can also use Fire Shield Sleeve for brake lines, fuel lines, wiring harnesses, and cables. In addition the rugged silicone coating makes this heat shield sleeve ideal for protecting welding lines and cables.  This sleeve is designed to reduce and dissipate heat and works great for areas where harsh environments exist that require heat shield insulation. HP Fire Armor Sleeving withstands 500°F continuous and brief intervals of 900°F.

Install Exhaust Wrap


Required equipment: safety glasses, dust mask, gloves, scissors or utility knife

Pretty easy, just cut to length!

Pro Tip: Compress or “bunch” the sleeve length wise, and stretch the opening of the sleeve then slide over. It may also help to coat fitting or terminal with silicone or dry graphite spray before sliding over. To decrease the id of sleeve after it slides over fitting/terminal pull on both ends of the sleeve to stretch the length.

MSDS | Specification Sheet | Brochure | Brochure (Printer Friendly)


Insulation Type: Dissipates heat

AN SLEEVING CALCULATOR

Disclaimer:

The following conversion is a guide for AN hoses only. The conversion reflects the most common conversions for AN hose sizes, however there may be some variances with different manufactureres. Always double check by measuring the OD of your hose. Always verify the OD of your hose, you may use a caliper or sliding an open end wrench over the hose. If you are still unsure verify with the manufacturer of the hose as to their specific OD. By using this calculator you acknowledge this is a guide only and it is ultimately your responsibility to verify the correct OD of your AN line.

ENTER AN HOSE SIZE WITHOUT DASH:

:

RESULTS:

 

:

:

:

Use HD Fire Shield Sleeve on:

  • Wire looms
  • Hydraulic lines
  • Oil lines
  • Fuel lines

heatshieldproducts (844) 723-2665