HD Thermaflect Sleeve

HD Thermaflect Sleeve

More Views

1100°F

593°C

CONTINUOUS

2000°F

1093°C

Intermittent

FEATURES:

  • Continuous operating reflective temperature of 1100°F, 2000°F intermittent

  • Capable of reducing up to 90% of radiant heat

  • Helps to lower air intake temperatures, protects wires from melting

  • Also available in a hook and loop seam

  • Larger diameters and rolls are available upon special request

  • Made in the USA

Part No Description
HD27011 1/2 in x 10 ft Sewn
HD27012 1/2 in x 25 ft, sewn external hem
HD27021 3/4 in x 10 ft
HD27022 3/4 in x 25 ft sewn
HD27101 1 in x 10 ft, sewn
HD27102 1 in x 25 ft sewn
HD27151 1-1/2 in x 10 ft sewn
HD27152 1-1/2 in x 25 ft, sewn
HD27201 2 in x 10 ft, sewn
HD27202 2 in x 25 ft, sewn
HD27251 2-1/2 in x 10 ft, sewn
HD27252 2-1/2 in x 25 ft, sewn
HD27301 3 in x 10 ft, sewn
HD27302 3 in x 25 ft, sewn
HD27351 3-1/2 in x 10 ft, sewn
HD27352 3-1/2 in x 25 ft, sewn
HD27401 4 in x 10 ft, sewn
HD27402 4 in x 25 ft, sewn
HD27451 4-1/2 in x 10 ft, sewn
HD27452 4-1/2 in x 50 ft, sewn
HD27501 5 in x 10 ft, sewn

Shield your wiring, lines, hoses, and from engine and tier 4 exhaust heat! Thermaflect Sleeve acts as a thermal barrier capable of reflecting up to 90% of radiant heat away (requires minimum of 1" of airspace and good airflow). It weighs a fraction of what silicone coated shield sleeves do and it offers superior radiant heat insulation. Thermaflect Sleeve withstands 1100°F of continuous radiant heat and 500°F direct heat. Ever notice your increased fuel mileage in the winter? Use these heat shield sleeves on your intercooler pipes to keep those intake temperatures down even in the summer! Also available in a hook and loop seam.

 



 

Be sure ends of sleeve are sealed or secured to component you are trying to protect. You can seal the ends using our Thermaflect Tape, Cool Foil Tape, Thermal-Tie, shrink tube, or any mechanical fastener. Securing the ends will ensure no hot air sneaks in behind the sleeve, thus allowing it to work more efficiently.

SDS | Specification Sheet | Brochure


Insulation Type: Barrier, reflect radiant heat

AN SLEEVING CALCULATOR

Disclaimer:

The following conversion is a guide for AN hoses only. The conversion reflects the most common conversions for AN hose sizes, however there may be some variances with different manufactureres. Always double check by measuring the OD of your hose. Always verify the OD of your hose, you may use a caliper or sliding an open end wrench over the hose. If you are still unsure verify with the manufacturer of the hose as to their specific OD. By using this calculator you acknowledge this is a guide only and it is ultimately your responsibility to verify the correct OD of your AN line.

ENTER AN HOSE SIZE WITHOUT DASH:

:

RESULTS:

 

:

:

:

Use HD Thermaflect Sleeve on:

  • Intercooler pipe
  • Air brake lines
  • Wiring looms
  • Hydraulic lines
  • AC Lines

heatshieldproducts (844) 723-2665